Roller Coaster
Thanks to Otter, Matt.in.Alba, Skogbit, BitterBricker, FlickBrick240, Graham, Dewey Brix, oprypin, Julien Mahin for helping identify parts
Bag inventory
1
Brick, Round 1 x 1
Minifigure, Hair Short, Bob Cut
Plate, Modified 2 x 2 with Wheels Holder Wide and Hole
Slope, Curved 2 x 1 x 2/3
Technic, Axle 2L Notched
Technic, Pin 1/2 without Friction Ridges
Plate 4 x 4
Plate, Round 1 x 1 with Flower Edge (5 Petals)
Minifigure, Hair Female Short Tousled with Side Part
Cone 2 x 2 x 1 2/3 with Stacked Rings (Beehive / Cotton Candy)
Minifigure, Head (Plain)
Plate, Round 1 x 1
Tile 2 x 2 Corner
Vehicle, Spoiler 1 x 4 on 1 x 2 Base
Hinge Plate 1 x 2 Locking with 1 Finger on End without Bottom Groove
Plant Flower Stem with Bar and 6 Stems
Brick 1 x 1
Brick, Round Corner 2 x 2 Macaroni with Stud Notch and Reinforced Underside
Frog
Plant Plate, Round 1 x 1 with 3 Layered Leaves
Plate, Modified 1 x 2 with 1 Stud with Groove and Bottom Stud Holder (Jumper)
Plate, Modified 2 x 2 with Groove and 1 Stud in Center (Jumper)
Plate, Round 1 x 1 with Flower Edge (5 Petals)
Tile 1 x 2 with Currency / Money, 100 Bill / Note Pattern
Tile, Round 1 x 1 Quarter
Bar 1L with Clip Mechanical Claw - Cut Edges and Hole on Side
Bar Holder with Handle
Brick, Modified 1 x 2 x 2/3 with Studs on Sides and Extended Stud Receptacle
Hinge Brick 1 x 2 Top Plate
Minifigure, Hair Short Swept Back with Sideburns and Widow's Peak
Plate 1 x 10
Plate 1 x 2
Plate 1 x 3
Plate 1 x 4
Plate 1 x 6
Plate, Modified 1 x 2 with Clip on End (Horizontal Grip)
Plate, Modified 1 x 2 with Clip with Center Cut on Top
Slope 45 2 x 1 with 2/3 Cutout
Technic Bush 1/2 Smooth
Technic, Disk 3 x 3
Tile 1 x 1 with Black and Red Digital Keypad Pattern
Tile 1 x 1 with White and Red Gauge, Black Thick Needle and Screw Heads Pattern
Tile 1 x 2
Tile 1 x 4
Tile 1 x 8
Tile, Modified 1 x 1 with Open O Clip
Tile, Modified 1 x 2 with Bar Handle
Wheel 31mm D. x 15mm Technic
Plant Grass Stem
Hips and Legs Plain
Legs Short
Plate 1 x 2
Plate 2 x 2
Tile 2 x 3
Minifigure, Headgear Cap - Short Curved Bill
Brick, Modified 1 x 1 with Studs on 4 Sides
Cone 1 x 1 with Top Groove
Plant Flower Stem with Bar Holder, Bar, and 3 Stems
Technic, Axle Connector 2L (Smooth with x Hole + Orientation)
Technic, Axle Connector Hub with 4 Bars and Pin Hole
Tile, Modified 1 x 1 with Open O Clip
Tile, Round 1 x 1 Quarter
Hips and Legs Plain
Bracket 1 x 2 - 2 x 2 Inverted
Panel 1 x 4 x 3 with Side Supports - Hollow Studs
Plate 2 x 2
Plate, Modified 1 x 2 with Door Rail
Plate, Modified 2 x 2 x 2/3 with 2 Studs on Side
Plate, Round 1 x 2 with Open Studs
Technic, Axle 1L with Pin without Friction Ridges with Round Hole
Tile, Modified 2 x 2 with Pin
Torso Knit Cable Sweater with Dark Tan Pattern / Tan Arms / Yellow Hands
Wheel Wheelchair with Molded Black Hard Rubber Tire Pattern
Windscreen 4 x 4 x 1 2/3 Canopy Dome Half Sphere with Bar Handle
Tile 1 x 2
Tile 1 x 4
Minifigure, Utensil Umbrella Top with No Bottom Flaps, 6 x 6 with Top Stud
Bar 4L (Lightsaber Blade / Wand)
Bar 6L with Stop Ring
Bracket 1 x 2 - 1 x 2 Inverted
Plate 1 x 2
Plate 2 x 8
Plate, Modified 1 x 1 with Open O Clip (Horizontal Grip)
Plate, Modified 1 x 2 with 2 Open O Clips (Horizontal Grip)
Torso Female Blouse with Buttons, Dark Pink Panel and Name Badge Pattern / White Arms / Yellow Hands
Torso Halter Top with Green Apples and Lime Spots and Back Print Pattern / Yellow Arms / Yellow Hands
Minifigure, Head Dual Sided Child Black Eyebrows, Reddish Brown Freckles, Grin / Sad Frown Pattern
Minifigure, Head Dual Sided White Bushy Eyebrows, Goatee, Wrinkles, Smile / Open Mouth Scared Pattern
Minifigure, Head Female Black Eyebrows and Eyelashes, Dark Orange Lips, Open Mouth Smile with Teeth Pattern
Frequently asked questions
-
This bag inventory was built by following the official LEGO building instructions step by step. At every step, we recorded which pieces were used and which numbered bag they came from, resulting in a complete parts list per bag.
-
Each numbered bag contains a specific subset of the set's total parts. By selecting a bag above, you can see every piece it includes — with part images, color details, and exact quantities.
-
Click on a bag, then use the export buttons in the toolbar. You can download a PDF for easy reference, or a BSX file — a BrickLink-compatible XML format you can import into tools like BrickStore.
-
We use bag 0 to list all parts that are outside of numbered bags, such as sticker sheets or some larger parts that are often not in any bag but directly in the box.
-
Since inventories are built by hand, mistakes can happen. If you spot anything wrong, please contact us so we can review and correct it.
Report an issue
Let us know what seems wrong with this bag inventory.
PDF format
Choose a layout for your PDF export.
Generating PDF
The inventory PDF for this bag is being generated. This may take a few seconds.